Dryer and Washer Repair in Winder, GA — $99 Flat, Plus Parts

Call a typical in-home appliance repair company and here's what happens: a $100–150 "diagnostic fee" just for the truck to show up, then labor billed on top, then parts, then a second visit when the part arrives. It's not unusual for a $40 belt to become a $350 invoice. That's not a repair bill — that's a down payment on a machine.

We flipped it. You bring the machine to our Winder shop, and repair is $99 flat labor plus the cost of parts. No trip charge, no diagnostic fee, no hourly meter running. The reason it's cheap is simple: you did the driving, so you're not paying for our truck, our fuel, and our tech's drive time. You're paying for the fix.

Drop-off is why the price stays this low — no truck fee, no drive time. Can't bring the machine in? We also offer in-home repair for top-load washers and standard electric dryers, about $165 plus parts, quote first — details below.

Yes, for some machines. Here's how the two options compare:

• Drop-off repair (any washer or electric dryer): $99 flat labor plus parts. Bring it to our Winder shop, by appointment.
• In-home repair (top-load washers and standard electric dryers only): about $165 plus parts, quote first. We come to you within about a 45-minute drive of Winder — Statham, Bogart, Bethlehem, Jefferson, Hoschton, Braselton, Auburn, Athens, Watkinsville, Monroe, Commerce, Dacula, Loganville, Grayson, Lawrenceville, Gainesville, and Oakwood are all in range. Not sure if you're in range? Call or text 706-995-6964 with your address. Farther away, drop-off repair at the shop is still $99 flat.

Front-load washers, stacked units, compact units, and washer-dryer combos are drop-off only — bring those to the shop. And if you're renting from us, repairs are already free; this pricing is only for machines you own.

A surprising share of no-heat, no-spin, and no-drain problems can be fixed at home for free — a tripped breaker, a clogged pump filter, a worn lid switch. Call or text 706-995-6964 and we'll walk you through it over the phone, free, for up to 20 minutes — one issue per person. Details on the free phone troubleshooting. If phone help can't fix it, drop-off repair is the next step. Already called us? Filling out the form still puts your info in our system so everything's ready when you book.

Usually it's one of a few known causes: a kinked or clogged drain hose, a clogged drain pump or pump filter, an out-of-balance or overloaded load, or a worn lid switch on a top-load washer. These are common failure points, not a sign the whole machine is finished.

What you can check safely:

• Unplug the washer before you reach behind, under, or into it.
• Look at the drain hose for kinks or a crushed bend behind the machine, and make sure nothing is blocking the standpipe or sink it drains into.
• If your model has an accessible drain pump filter, check it for socks, coins, and hair ties (your manual shows where it is). Have towels ready — water in the tub will come out.
• For a washer that won't spin, redistribute the clothes so the load is even and take some out if it was overloaded. Make sure the lid closes fully.

When to bring it in: if the hose is clear and the load is balanced but it still won't drain or spin, a part has probably failed — a pump, a lid switch, or a belt. Drop-off repair is $99 flat labor plus parts, quoted before we start. For top-load washers we can also come to you for about $165 plus parts, quote first (front-load washers are drop-off only). Not sure which it is? Try our free washer troubleshooting first, or call or text 706-995-6964.

If the drum turns but the air stays cool, the problem is usually on the heat side, not the whole dryer: a tripped breaker, a clogged vent, a blown thermal fuse, or a failed heating element (igniter on a gas dryer).

What you can check safely:

• Check the breaker. An electric dryer uses a double breaker, and when only one half trips the drum can still turn with no heat — make sure both halves are fully on.
• Clean the lint screen, then run the dryer and see whether warm air pushes open the flap outside.
• Unplug the dryer before you pull it away from the wall or look at the vent hose behind it.
• Gas dryer? If you ever smell gas, leave the home and call your gas utility or 911. Beyond the lint screen and vent, leave gas parts to a pro — we repair electric dryers only and don't service gas dryers right now.

When to bring it in: if the breaker is fine and the vent is moving air but there's still no heat, it's most likely a thermal fuse or heating element — inexpensive parts that we replace at the bench for $99 flat labor plus parts. A blown thermal fuse is often a sign the vent is clogged, so if airflow is weak, book dryer vent cleaning too — otherwise the new part can burn out again. Standard electric dryers can also be repaired at home for about $165 plus parts, quote first. Call or text 706-995-6964, or start with the free dryer troubleshooting.

A squeal or rumble while the drum turns usually points to a worn belt or worn drum rollers. A rattle or thump can be as simple as something caught in the drum or a dryer that isn't sitting level.

What you can check safely:

• Unplug the dryer first.
• Empty the drum and check for coins, buttons, or small items caught around the drum.
• Press on the top corners to see whether the dryer rocks, and adjust the feet until it sits level.

When to bring it in: if it still squeals or thumps with an empty drum, the belt or rollers are the likely cause. Both are known fixes on the platforms we work on — $99 flat labor plus parts at our Winder shop, or about $165 plus parts at your home for a standard electric dryer, quote first. Describe the sound when you call or text 706-995-6964 and we'll tell you what it usually is. More symptoms are on our free phone troubleshooting.

If your dryer runs but doesn't heat, tumbles but squeals, or shuts off mid-cycle, you're describing the most common repairs in the business: heating elements, thermal fuses, belts, and rollers. On the platforms we work on — Whirlpool, GE, Maytag, Kenmore, Amana, Roper, Estate, Hotpoint, and Samsung — these are well-understood fixes with cheap, available parts. Most dryer repairs land well under what a single in-home service call costs before any actual repair happens.

Washer problems — won't spin, won't drain, won't fill, walks across the floor, leaves clothes soaked — are the same story: known failure points on proven top-load machines, fixed at a bench by people who do it daily.

Clothes taking two cycles to dry? It might not be the dryer at all — it might be the vent. We offer $99 dryer vent cleaning, too.

Repair isn't a side hustle for us — it's the middle of our whole business. We refurbish washers and dryers all day, every day, for our rental fleet and sales floor. Our techs aren't guessing at your machine from a YouTube video in your laundry room; they're working on their fifty-somethingth Whirlpool of the month at a bench with the parts on the shelf behind them.

That volume is also why we're honest about the other direction —

Some machines aren't worth the part. A 22-year-old washer with a seized transmission doesn't need $200 of surgery — it needs a dignified exit. When that's the truth, we say so before you spend a dime, and then you've got the easiest next steps in town:

• We'll take the dead machine off your hands free — no disposal fee, no hauling it back home.
• Replace it with a refurbished machine with a 3-month warranty — singles from $165 at shop pickup, and you're already standing in the shop.
• Or skip ownership headaches entirely and rent for $70/month with every future repair free. If you're tired of fixing machines, that last one is the permanent cure.

1. 1

   Call or text 706-995-6964 first. Describe the problem — we'll tell you honestly whether it sounds worth fixing, roughly what the part usually runs, and set your drop-off appointment. (The shop is by appointment; we'll send you the address when you book.)

2. 2

   Bring the machine in. Truck, trailer, buddy's van — we'll help you unload.

3. 3

   We diagnose and call you with the parts price before doing the work. $99 labor + the part, approved by you first. No surprise totals.

4. 4

   Pick it up working. Most common repairs turn around in a few days, parts availability depending.